Instructions & Guides
Instructions & Guides
Off the table. Onto the wall.
Every Sofishticated mount, frame and case is engineered to go up in minutes. Find your product below for the official step-by-step install — plus care and removal tips.
F1 Speed Champions Wall Mounts
For single Speed Champions cars. No tools, no drilling — just peel, press and place.
Peel off the backing
Wipe your chosen wall spot clean and dry, then remove the adhesive backing from the rear of the mount.
Line up & hold
Line the mount up level and hold it firmly against the wall for 10 seconds.
Place your car
Slot your LEGO® Speed Champions car onto the mount. Your build is now the hero.
LEGO® Technic™ F1 Wall Mounts
Install the mount the same way as our adhesive mounts — peel, hold firmly for 30 seconds, and let it cure for 2 hours before loading. Then hook your car onto the mount at the correct point below.
Mercedes W14
Centre of chassis, between the rear axle and cockpit — align the mount pin with the central Technic beam.
Red Bull RB20
Rear undercarriage above the diffuser — hook the mount onto the cross-beam between the rear wheels.
McLaren MCL39
Side-pod underside channel — slot the mount pin into the exposed orange-marked Technic axle visible from beneath.
Ferrari SF-24
Centre spine behind the front axle — the red/orange gearbox block marks the zone; insert the mount pin just forward of it.
LEGO® F1 Helmet Wall Mounts
For the Hamilton & Leclerc helmet builds. This mount screws into the wall for a solid, permanent hold.
Mark the holes
Hold the mount where you want it, check it's level, and mark the screw-hole positions on the wall.
Drill & fix
Drill the marked points and screw the mount firmly into the wall. Use wall plugs suited to your surface (plaster, brick or timber).
Seat the helmet
Rest your LEGO® F1 helmet into the mount so it sits balanced and secure.
F1 Speed Champions Framed Display
Your premium wall-mounted frame for Speed Champions cars. Includes a custom wall bracket and a Speed Champion mount. The same process applies to our Icons display frames.
Install the bracket
Attach the custom bracket to the wall by removing the adhesive backing. Make sure it's straight and level before pressing it into place.
Remove protective plastic
Peel the protective plastic off the perspex — note there's a film on both the front and back.
Install the Speed Champion mount
Remove its adhesive backing and fit the Speed Champion mount inside the frame, aligned 3 cm up from the bottom of the grid box.
Hang the frame
Hang the frame on the wall bracket from Step 1. It should slide into place with no lateral movement.
Mount your car
Mount your LEGO® Speed Champion onto the bracket. You're all set — enjoy your display!
Build a wall
Frames line up edge to edge — perfect for a full grid or season line-up.
F1 Mini Collectable Framed Display
Display your full set of LEGO® mini F1 cars in a printed perspex frame, using the provided 2×1 LEGO plates.
Install the bracket
Attach the custom bracket to the wall by removing the adhesive backing. Keep it straight and level before pressing it into place.
Remove protective plastic
Peel off the protective plastic from both the front and back of the perspex.
Install the 2×1 LEGO plates
Glue the provided 2×1 LEGO plates to the outside of the perspex, following the printed outline in the artwork underneath.
Mount your minis
Once the glue has fully dried, mount your LEGO® mini F1 cars onto the plates you just installed.
Hang up your display
Mount the finished display to the wall and enjoy your new showcase!
Let glue cure
Give the glue plenty of time to set before mounting cars so the plates hold firmly.
Minifigure Display Cases
The 25 × 25 cm case holds a full set of 12 minifigures, each raised on its own podium against a printed backing.
Glue the podiums
Glue the provided 12 podiums onto the guide marks printed on the paper backing.
Mount your minifigures
Once the glue has set, place each of your minifigures onto its podium.
Mount the case
Wipe your chosen wall spot clean, then mount the case to the wall and enjoy your collection on display.
Caring for & Removing Your Mount
Our acrylic adhesive is engineered to be strong while you want it — and clean to remove when you don't.
Warm the adhesive
Run a hairdryer over the mount for 20–30 seconds. A little heat softens the bond.
Peel slowly
Lift one edge and peel the mount away slowly and evenly — no sudden yanks.
Reposition or store
Removes cleanly without damaging paint or plaster. Use a fresh adhesive pad to remount.
Frequently asked questions
Will it take off my wall paint?
No. Our wall-mount adhesives are designed to be used safely on all painted wall surfaces and can be removed cleanly without damaging the wall.
Will it hold my LEGO® Speed Champion?
Yes. The adhesive supports up to 10× the weight of a single LEGO Speed Champions car, so you've got nothing to worry about.
Is the mount removable?
Yes. We use a high-quality acrylic adhesive engineered to be removable. A little heat from a hairdryer softens the bond, letting you peel the mount away cleanly — perfect if you ever want to reposition it or take it down.
How do I know where to hang my Technic car?
See the Technic Mounting Points guide above for the exact spot on each model (Mercedes, Red Bull, McLaren and Ferrari). When in doubt, flip the car upside-down to confirm the mounting point before installing.
Can I mount on brick, timber or concrete?
Our included frame brackets are tailored for plaster walls. For brick, timber or concrete, please use suitable fixings or consult a professional installer.
Are LEGO® models included?
No — our products are the mounts, frames and cases only. The LEGO® build is yours; we just hold it up.
Need a hand?
Can't find a guide for your set, or want something made to measure? We're here to help.
Contact us